Think Green, Act Blue ©
Best HHO Electrolyte
The best HHO Electrolyte (catalyst) for my HHO Gas Generator?
Use an electrolyte that suits the best to you HHO Gas generator design. The distance between the electrode plates does really matter.
A - For electrodes with little distance between the plates you could use: tap water or distilled- rain- or demi water with a very little of any of the catalysts mentioned below.
B - For electrodes with more space between the plates tap water won't work. So use distilled- rain- or demi water with a little of the catalysts mentioned below.
C - For electrodes with a lot of space between the plates tap water won't work. Use distilled- rain- or demi water with a one of the catalysts mentioned below.
1 - Tap Water - H2O (containing minerals, salts etc.)
Advantages:
- Available everywhere
- Cheap
- Safe
Disadvantages:
- Water might turn brown with smudge on the electrodes
- Water that contains chlorine should not be used
The best water for a HHO generator we found to be: Bottled Mineral Water
Distilled water is not recommended (anylonger..)
2 - White Vinegar - acetic acid - H3C-COOH
Advantages:
- Stainless electrodes stay clean
- Available everywhere
- Cheap
- Safe
Disadvantages:
- Smells
- water will become dark
Available at your local grocery store.
A good mix for medium distance electrodes: 100% vinegar with (only if necessary) some baking soda. (If do so be carefull, because the reaction will produce co2 and some other gasses!)
2 - Baking Soda ( Natriumbicarbonate ) NaHCO3
Advantages:
- Available everywhere
- Cheap
Disadvantages:
- Electrodes and water might turn brown
- Produces Co2 (30%) and Co (4%).
- For this reason not recommended
Pure Baking Soda might leave a brown tinted residu.
3 - Sodium Hydroxide also called Lye = NaOH
Advantages:
- Electrodes stay clean
- Cheap
- 95 - 100% pure HHO (oxygen hydrogen) Gas production with right generator design
- Available in the Grocery store
Disadvantages:
- Limited dangerous to work with
- Too much heat causes corrosion
Pure sodium hydroxide is a white solid; available in pellets, flakes, granules and as a 50% saturated solution. It is deliquescent and readily absorbs carbon dioxide from the air, so it should be stored in an airtight container. It is very soluble in water with liberation of heat. Use with distilled water.
4 - KOH
Also called pottassium hydroxide.
Advantages:
- Electrodes stay clean
- 95 - 100% pure HHO gas production along with the right generator design
- strong and pure electrolyte
Disadvantages:
- Not available everywhere
- dangerous to work with
Recommended as very good electrolyte (recommended by Honda in 2001)
5 - K2CO3
Pottassium Carbonate.
Advantages:
- Non aggressive
- Reasonable / good HHO gas production depending on HHO cell design
- Cheap
- Safe to work with
Disadvantages:
- It is possible (sometimes necessary) to mix it with a little Koh to draw more amps.
Winter Electrolyte:
Developed by mr. M. Moldoveanu
Water+Ethyl Glycol+KOH will provide the benefit the technical of low freezing point but high boiling point at the same time.
General information to get the best results:
Use destilled water or bottled mineral water only.
For the flat-plate-design electrodes you might want to consider pulse power to get more efficiency, sometimes using less amps. PWM helps to keep the temperature low in the HHO Cell. Different designs available f.e. the Stanley Meyer like PWM. More information about PWM. More information at HHO electrodes
For most cars between 10 - 30 amps should give good results. Prevent to add too much watervapour into Diesel engines. Too much watervapour could delay the ignition of the fuel mixture which might cause using more fuel.
Do not try to get too much HHO gas volume out of your generator by using a lot of amps etc. It will certainly become overheated and your electrodes could be damaged. Or you will generate steam. It is better to a larger number of (small) generators to get the gas volume you need. Or use a HHO generator with a pump system. Advantages: The generators will stay cool / warm, uses less power, is safer and will last longer(!)
Your optimum draw should be several amps less when cold so keep adding little by little. until you get to your optimum amp draw. (sometimes it will double)
More IMPORTANT information at our Fuel Saver page
A few Golden Basic HHO rules in a nutshelf:
- Distance between plates > 3mm
- Electrodes should be made of 316 L stainless steel
- Use distilled water and KOH for electrolyte
- Don't exceed 1,8 volts between the plates
- Keep the HHO Cell temperature under 50 Celsius always
- take care of safety!
|
E3 FA - Exclusively by
Brownsgas.com
|
E3-10LPM FUEL ASSISTANT
- Top Design & Quality
- Engines up to 500HP
- Save Diesel, Propane or Gas
- Highest Safety Standards
- Quality Guarantee
- 240 or 110 volts
- Shipped in Wooden Crate
- Worldwide DHL Shipping
- More information (PDF)
Limited Time Introduction Offer
|
Save
up
to
30%
|
Environment
Friendly
|
Brownsgas.com 2004 - 2009
Top of page
